Features
• Excellent adhesion to most plastic, vinyl, and paper
• Fast curing
• Opaque or Transparent Pantone colors

Opaque Pantone Colors
KC-74-100 Mixing Base
KC-74-101 Yellow
KC-74-102 Warm Red
KC-74-103 Rubine Red
KC-74-104 Rhodamine Red
KC-74-105 Purple
KC-74-120 Violet
KC-74-106 Process Blue
KC-74-107 Reflex Blue
KC-74-108 Green
KC-74-109 Mixing White
KC-74-110 Mixing Black

Four-Color Process
KC-74-400 Halftone Base
KC-74-401 Yellow

KC-74-402 Magenta
KC-74-403 Cyan
KC-74-404 Black

Opaque Colors
KC-74-111 Opaque White
KC-74-112 Opaque Dense Black
KC-74-113 Primrose Yellow
KC-74-115 Medium Yellow
KC-74-114 Brilliant Orange
KC-74-116 Fire Red
KC-74-125 Bright Red
KC-74-117 Scarlet Red
KC-74-118 Navy Blue
KC-74-119 Peacock Blue
KC-74-120 Royal Violet
KC-74-121 Emerald Green
KC-74-122 Deep Green
KC-74-123 Lt. Brown
KC-74-124 Dk. Brown

Metallic Colors
KC-74-901 Silver
KC-74-903 Palegold
KC-74-904 Rich Palegold
KC-74-905 Richgold

Modifiers
KC-8201 Anti-Bubble #1
KC-8203 Diluent #1 (Flexible)
KC-8204 Diluent #2 (Same Flex)
KC-8205 Diluent #3 (Rigid)
KC-8206 Flow Promoter
KC-8207 Sensitizer #1
KC-8208 Sensitizer #3 Waterwhite
KC-8209 Sensitizer #7 Opaque
KC-8210 Adhesion Promoter

Biodegradable Wash-Up
SYS-2500 Screen Wash
SYS-2510 Screen Wash Gel

Packaging:
Inks: Quart, gallon, and 5-gallon pails
Solvents: Pints, quarts, and gallons

Designed for cylinder as well as flat-bed printing. It is called Multi King because of its excellent intercoat adhesion properties for multi color printing and its ability to adhere to many plastic, vinyl and paper substrates. All colors shown to the left are available in a matt or gloss finish which must be specified when ordering. Ten fluorescent colors are also available.

SPECIFICATIONS:

USES: Styrene, acrylic, PVC, polycarbonate, TC polyester, TC aluminum, limp and supported vinyl, paper and paperboard.

FINISH: Dries to a matte or gloss finish.

OPACITY: Good opacity on most substrates.

COVERAGE: Using 390 mesh, approximately 3200 square feet per gallon

DRYING TIME: Multi King inks cure in air upon brief exposure (2-5 seconds) to a focused high intensity ultraviolet light source standard 200 watt/inch medium pressure mercury vapor lamp. Speed of cure is approximately 60-80 fpm when passed through a conveyorized UV curing module containing 1x200 watt bulbs properly focused. Additional curing speeds can be achieved by adding 2-3% liquid sensitizer.

SCREEN FABRIC: Monofilament polyester or nylon, 350-390 mesh per inch recommended. Acceptable 305-420 mesh per inch. (Open area should not exceed 30%)

FILM THICKNESS: Recommended 0.4 to 0.6 mil (10-15 microns)

SCREEN COATING, FILM, BLOCKOUT: Lacquer proof stencil, most direct or direct/indirect work well.

MODIFIERS: To lower viscosity use Diluent #1 or Diluent #3. To increase curing speed add Sensitizer #1, or Sensitizer #7. To eliminate any bubbles in the screen use Anti-bubble #1

WASHUP: Screen cleans with SYS-1925 or a special high flash point wash containing no hydrocarbon solvents such as biodegradable washes SYS-2500 or SYS-2510 Gel.

STORAGE/HANDLING/WARNINGS: See product data sheet.

ALWAYS TEST PRINT BEFORE PRODUCTION