Features
• Adhesion to treated polyethelene
• Very flexible / Chemical Resistant
• Excellent for bottle printing

Opaque Pantone Colors
KC-71-100 Mixing Base
KC-71-101 Yellow
KC-71-102 Warm Red
KC-71-103 Rubine Red
KC-71-104 Rhodamine Red
KC-71-105 Purple
KC-71-120 Violet
KC-71-106 Process Blue
KC-71-107 Reflex Blue
KC-71-108 Green
KC-71-109 Mixing White
KC-71-110 Mixing Black

Four-Color Process
KC-71-400 Halftone Base
KC-71-401 Yellow
KC-71-402 Magenta
KC-71-403 Cyan
KC-71-404 Black

Opaque Colors
KC-71-111 Opaque White
KC-71-112 Opaque Dense Black
KC-71-113 Primrose Yellow
KC-71-115 Medium Yellow
KC-71-114 Brilliant Orange
KC-71-116 Fire Red
KC-71-125 Bright Red
KC-71-117 Scarlet Red
KC-71-118 Navy Blue
KC-71-119 Peacock Blue
KC-71-120 Royal Violet
KC-71-121 Emerald Green
KC-71-122 Deep Green
KC-71-123 Lt. Brown
KC-71-124 Dk. Brown

Metallic Colors
KC-71-901 Silver
KC-71-903 Palegold
KC-71-904 Rich Palegold
KC-71-905 Richgold

Modifiers
KC-8201 Anti-Bubble #1
KC-8203 Diluent #1 (Flexible)
KC-8204 Diluent #2 (Same Flex)
KC-8205 Diluent #3 (Rigid)
KC-8206 Flow Promoter
KC-8207 Sensitizer #1
KC-8208 Sensitizer #3 (Waterwhite)
KC-8209 Sensitizer #7 (Opaque)
KC-8210 Adhesion Promoter

Biodegradable Wash-Up
SYS-2500 Screen Wash
SYS-2510 Screen Wash Gel

Packaging: Quart, gallon, and 5-gallon pails

Excellent adhesion on treated polyethylene and polypropylene surfaces. Very flexible and chemical resistant. Fast curing speed for hi-speed bottle printing. All colors shown to the left are available in a matt finish which must be specified when ordering. Ten fluorescent colors are also available.

SPECIFICATIONS:

USES: For bottles and container decorating. For treated polyethylene, PVC, PET, and many other substrates. Cured film will be flexible and provide chemical,water,and mar-resistance.Can cure at speeds up to 100 containers per minute.

FINISH: Dries to a flexible matte or gloss finish.

OPACITY: Good opacity on most substrates.

COVERAGE: Using 390 mesh, approximately 3200 square feet per gallon

DRYING TIME: 7100 Series inks cure in air upon brief exposure (2-5 seconds) to a focused high intensity ultraviolet light source standard 200 watt/inch medium pressure mercury vapor lamp. Speed of cure is approximately 80-90 fpm when passed through a conveyorized UV curing module containing 1x200 watt bulbs properly focused. Additional curing speeds can be achieved by adding 2-3% liquid sensitizer.

SCREEN FABRIC: Monofilament polyester or nylon, 350-390 mesh per inch recommended. Acceptable 305-420 mesh per inch. (Open area should not exceed 30%)

FILM THICKNESS: Recommended 0.4 to 0.6 mil (10-15 microns)

SCREEN COATING, FILM, BLOCKOUT: Lacquer proof stencil, most direct or direct/indirect work well.

MODIFIERS: To lower viscosity use Diluent #1 or Diluent #2. To increase curing speed add Sensitizer #2, or Liquid Opaque Sensitizer. To eliminate any bubbles in the screen use Anti-bubble #1

WASHUP: Screen cleans with SYS-1925 or a special high flash point wash containing no hydrocarbon solvents such as biodegradable washes SYS-2500 or SYS-2510 Gel.

STORAGE/HANDLING/WARNINGS: See product data sheet.

ALWAYS TEST PRINT BEFORE PRODUCTION