Features
• Excellent adhesion to Plastic
• Opaque or Transparent
   Pantone colors

Opaque Pantone Colors
KC-4100 Mixing Base
KC-4101 Yellow
KC-4102 Warm Red
KC-4103 Rubine Red
KC-4104 Rhodamine Red
KC-4105 Purple
KC-4120 Violet
KC-4106 Process Blue
KC-4107 Reflex Blue
KC-4108 Green
KC-4109 Mixing White
KC-4110 Mixing Black

Four-Color Process
KC-4400 Halftone Base
KC-4401 Yellow
KC-4402 Magenta
KC-4403 Cyan
KC-4404 Black

Opaque Colors
KC-4111 Opaque White
KC-4112 Opaque Dense Black
KC-4113 Primrose Yellow
KC-4115 Medium Yellow
KC-4114 Brilliant Orange
KC-4116 Fire Red
KC-4125 Bright Red
KC-4117 Scarlet Red
KC-4118 Navy Blue
KC-4119 Peacock Blue
KC-4120 Royal Violet
KC-4121 Emerald Green
KC-4122 Deep Green
KC-4123 Lt. Brown
KC-4124 Dk. Brown

Metallic Colors
KC-4901 Silver
KC-4903 Palegold
KC-4904 Rich Palegold
KC-4905 Richgold

Modifiers
KC-8201 Anti-Bubble #1
KC-8203 Diluent #1 (Flexible)
KC-8204 Diluent #2 (Same Flex)
KC-8205 Diluent #3 (Rigid)
KC-8206 Flow Promoter
KC-8207 Sensitizer #1
KC-8208 Sensitizer #3 Waterwhite
KC-8209 Sensitizer #7 Opaque
KC-8210 Adhesion Promoter

Biodegradable Wash-Up
SYS-2500 Screen Wash
SYS-2510 Screen Wash Gel

Packaging:
Inks: Quart, gallon, and 5-gallon pails
Solvents: Pints, quarts, and gallons

Excellent adhesion to most rigid and flexible plastic substrates
Works well for top-coated polyester, polycarbonate, acrylic, styrene, PVC and CAB. All colors shown to the left are available in a matt finish which must be specified when ordering. Ten fluorescent colors are also available.

SPECIFICATIONS:

USES: Plastic King II Membrane switches, signs, decals, P.O.P., control panels, name plates. Excellent gloss, adhesion and Intercoat adhesion.

USES: Plastic King III Membrane switches, signs, decals, P.O.P., control panels, name plates, plus top coated polyester, polycarbonate, styrene, acrylic, paper, etc. Excellent die cutting properties.

FINISH: Dries to a matte or gloss finish.

OPACITY: Good opacity on most substrates.

COVERAGE: Using 390 mesh, approximately 3200 square feet per gallon

DRYING TIME: Plastic King inks cure in air upon brief exposure (2-5 seconds) to a focused high intensity ultraviolet light source standard 200 watt/inch medium pressure mercury vapor lamp. Speed of cure is approximately 60-75 fpm when passed through a conveyorized UV curing module containing 1x200 watt bulbs properly focused. Additional curing speeds can be achieved by adding 2-3% liquid sensitizer.

SCREEN FABRIC: Monofilament polyester or nylon, 350-390 mesh per inch recommended. Acceptable 305-420 mesh per inch. (Open area should not exceed 30%)

FILM THICKNESS: Recommended 0.4 to 0.6 mil (10-15 microns)

SCREEN COATING, FILM, BLOCKOUT: Lacquer proof stencil, most direct or direct/indirect work well.

MODIFIERS: To lower viscosity use Diluent #1 or Diluent #2. To increase curing speed add Sensitizer #1, or Liquid Opaque Sensitizer. To eliminate any bubbles in the screen use Anti-bubble #1

WASHUP: Screen cleans with SYS-1925 or a special high flash point wash containing no hydrocarbon solvents such as biodegradable washes SYS-2500 or SYS-2510 Gel.

STORAGE/HANDLING/WARNINGS: See product data sheet.

ALWAYS TEST PRINT BEFORE PRODUCTION